How to Prevent Frozen Pipes: The Complete Guide

Share this:

Here is how to prevent frozen pipes: keep the heat on and steady, insulate and seal around pipes in unheated spaces, and shut off and drain outdoor faucets before the first freeze. During a hard freeze, let faucets on exposed pipes drip and open sink cabinet doors so warm air reaches the plumbing. Know where your main water shut-off valve is, because if a pipe freezes and splits anyway, closing it fast limits the damage. Below are the 10 steps in priority order. The sections after them explain why pipes burst and which pipes are most at risk. They also cover what to do before the cold, during a cold snap, while away, when the power fails and if a pipe freezes.

The Short Answer: 10 Steps to Prevent Frozen Pipes, in Priority Order

The steps are ordered by impact, most protective first, as a Bluebot editorial judgment drawn from the sources named in this guide. Start at the top and work down.

  1. Keep the heat on and steady, day and night. Leave the thermostat at one setting, including when you are away. Steady warmth in the walls helps every other step work.
  2. Insulate pipes in unheated spaces. Wrap pipes in crawl spaces, attics, garages and exterior walls with foam pipe sleeves, and use heat cable on lines you cannot keep warm.
  3. Disconnect garden hoses and drain each outdoor faucet. Close the indoor shut-off for the faucet, then open the faucet outside so the line empties.
  4. Seal drafts and air leaks near pipes. Close gaps where your pipes run near exterior walls, sill plates and vents, so cold air cannot blow across them.
  5. Let a faucet drip during a hard freeze. Choose a faucet on an exposed line. Running water, even a trickle, helps, and an open tap gives the pressure somewhere to go.
  6. Open sink cabinet doors on exterior walls. Room air can then reach your pipes behind the doors.
  7. Keep the garage door closed. This matters most when water lines run through the garage.
  8. Drain sprinkler and pool supply lines before the first freeze. Follow the manufacturer’s directions, or ask a pro.
  9. Find and test your main water shut-off valve before winter. Know where it is and confirm it turns.
  10. Have a plan for time away and power outages. Decide ahead who checks the house and what you will do if the heat goes out.

Why It Matters: How a Frozen Pipe Turns Into a Burst Pipe

Water expands as it freezes, but a pipe usually splits because an ice blockage traps water between the ice and a closed faucet. Pressure builds in that trapped section until the pipe gives way, often away from the ice itself.

That sequence comes from research, not guesswork. A 1996 report from the University of Illinois Building Research Council found that ice growth simply pushing on the pipe wall is not what bursts a pipe. Freezing first creates an ice blockage, and further ice growth then applies dangerously high pressure to the confined water.

The South Carolina Farm Bureau Insurance summary of that research describes the same pattern. Pressure rises downstream, between the blockage and a closed faucet, and the pipe usually bursts where little or no ice has formed.

For you, the practical point is that a split can stay hidden until the pipe thaws and water flows through it, sometimes inside a wall or ceiling. A pipe that held through a freezing night can start leaking once the house warms and the ice melts.

Once a pipe splits, how fast water damage spreads depends on how long the water runs before anyone notices. That is also why the drip in step 5 helps: an open tap gives the pressure somewhere to go.

Do not assume a frozen pipe that has not leaked yet is safe. The ice in the pipe may be holding the water back, and the leak can start at the thaw. Treat every frozen pipe as a pipe that could split, and thaw it carefully, as the section on signs of a frozen pipe explains below.

Which Pipes Freeze First: The Riskiest Spots in Your Home

The pipes most likely to freeze are the ones exposed to cold air, either outdoors or in unheated parts of the house. As of October 2026, the American Red Cross names many of the same trouble spots, so use this list as a walkthrough checklist for preventing frozen pipes:

  • Outdoor faucets (hose bibs) and the lines that feed them
  • Sprinkler and pool supply lines, which are exposed to severe cold
  • Pipes in crawl spaces and unheated basements
  • Pipes in attics
  • Pipes in garages, including water heater lines
  • Kitchen and bathroom sink lines on exterior walls
  • Pipes near foundation vents, sill plates or dryer vents

Frozen water pipes are not only a northern problem. The University of Illinois Building Research Council (1996) reported that freeze damage to pipes is more severe in the southern United States than in the north. Pipe protection is more consistent in the north.

The Farm Bureau Insurance summary adds why. In milder climates, pipes are more likely to run outside the building’s insulation. Homeowners tend to be less aware of freezing problems that may strike only once or twice a season, so a rare cold snap can catch those homes off guard.

PEX is more flexible than rigid pipe. The Plastics Pipe Institute (2026), an industry group for plastic pipe makers, says frozen PEX typically expands without cracking or splitting. Installation problems can still make it fail, and freezing should be prevented in any pipe.

Before the First Freeze: Fall Steps That Prevent Most Frozen Pipes

Fall is a good time to prevent frozen pipes, because a small cost now may prevent a much costlier repair after the first hard night. Work through these five on a mild weekend, and most of your protection will be in place before the forecast turns.

How to Insulate Exposed Pipes

The Insurance Institute for Business & Home Safety (IBHS, 2023) advises insulating exposed pipes and vents before temperatures dip below freezing. To protect pipes from freezing, slide foam pipe sleeves, sized to the pipe, over lines in crawl spaces, attics, garages and exterior walls. Tape the seams and joints, cover fittings and valves, and use fiberglass wrap in tight spots.

For a line you cannot keep warm, add thermostatically controlled heat cable listed by a recognized testing lab such as UL, and install it as the manufacturer directs. Heat tape versus insulation has its own guide.

Seal Air Leaks Near Pipes

Cold air that blows across a pipe can freeze it even when the room is warm. Caulk or spray foam gaps around pipe penetrations and sill plates. Seal the holes where cable or phone lines enter an outside wall, which the Farm Bureau Insurance summary says can give cold air access to pipes.

IBHS (2023) also advises temporarily covering or closing crawl space vents in winter. Check your local code first, because rules on crawl space vents vary by location.

Shut Off and Drain Outdoor Faucets

Disconnect every garden hose, then close the indoor shut-off valve that supplies each outdoor faucet. Open the faucet outside so the water drains, and leave it open so any water left in the pipe has room to expand. Finish with an insulated hose bib cover.

A hose you leave attached can trap water, even in a frost-free hose bib. The full procedure is the outdoor faucet guide in the Related guides block below.

Drain Sprinkler and Pool Lines

The American Red Cross advises draining sprinkler and pool supply lines by following the manufacturer’s or installer’s directions. It says not to put antifreeze in those lines unless directed. Whether to drain by gravity or blow the lines out depends on your system, so follow the sprinkler maker or hire a pro rather than guessing.

Find and Test Your Main Shut-Off Valve

Locate your main water shut-off valve. Tag it so anyone in the house can find it. Turn it fully closed and open once to confirm it moves. A valve that will not turn is better discovered in October than during a leak. If it sticks or drips, call a licensed plumber. The main shut-off guide is linked in the Related guides block below.

When a Hard Freeze Is Coming: What to Do on the Coldest Nights

When a hard freeze is forecast, keep the heat steady, let exposed lines drip, and get warm air to the pipes. These steps to keep pipes from freezing usually take minutes and cost little. Do them the evening before the cold arrives, then repeat them each night of the cold spell.

Keep the Thermostat Steady, Day and Night

Skip the overnight setback during a cold snap, because a cooler house at night can let the cold reach the pipes inside the walls. The American Red Cross advises keeping the thermostat at the same temperature day and night, and notes that a higher heating bill can prevent a much more costly repair. IBHS (2023) says to set the thermostat to at least 55°F. The thermostat guide in the Related guides block covers the full home-or-away answer.

Let the Right Faucets Drip

Pick faucets on exterior walls or fed by exposed pipes, and run a slow drip on both the hot and cold sides. The American Red Cross says running water, even a trickle, helps prevent freezing, and an open tap also gives the pressure explained above somewhere to go. Jeff Hunter, owner of Benjamin Franklin Plumbing, told Sherman, Texas, station KXII (2026) on January 20, 2026, to drip both the hot and the cold. His reason: “the hot water line when it’s stagnant can freeze over time.”

If your utility asks customers to limit dripping during a widespread freeze, follow that request. The drip guide covers how much and which faucets.

Open Cabinet Doors and Close the Garage

Open the cabinet doors under kitchen and bathroom sinks on exterior walls so room air reaches the pipes behind them, and leave the doors open through the cold spell. Move cleaning products and household chemicals out of reach of children and pets first. Keep the garage door shut, especially when supply lines or a water heater sit in the garage. A closed door holds back the cold and keeps wind off the pipes.

Know Your Trigger Temperature

In University of Illinois Building Research Council field tests (1996), as reported by Farm Bureau Insurance, freezing began in uninsulated pipes in an unconditioned attic. That happened when the outside temperature fell to 20°F or below.

Treat 20°F as an alert level, not a safe line. Wind, drafts through gaps, and a long cold spell can freeze pipes at warmer readings. Exact temperatures and timing are covered in the two freeze-temperature guides in the Related guides block.

Going Away in Winter: How to Protect an Empty House’s Pipes

When you leave in winter, you have two safe choices. Keep the heat on and have someone check the house, or shut off the main valve and drain the pipes. Pick one before you go, and never leave a house with the heat off and the water still running to it.

  • Keep the thermostat setting steady. As of October 2026, the American Red Cross says no lower than 55°F when you are away, and IBHS (2023) also says at least 55°F.
  • Open interior doors and sink cabinet doors so warm air moves around the plumbing.
  • Ask a neighbor, friend or house sitter to check the house regularly, and show them where the main valve is.
  • Give that person your contact details and your permission to call a licensed plumber if they find a problem.
  • For a longer absence, close the main valve and open faucets, starting on the top floor and working down, to drain the lines.

A seasonal or vacant home often needs a full winterization, such as draining the water heater and protecting drain traps, which the vacant-home guide covers. Some homeowners policies may expect you to take reasonable steps to keep heat on in an unoccupied home, so read your own policy before you leave. This guide draws on U.S. sources, so check local rules and utility requests where you live. Remote alerts, covered in the Bluebot section below, let you hear about trouble while you are away.

How to Keep Pipes From Freezing Without Power

When the power and heat go out in freezing weather, hold in the heat you have, keep water moving, and drain the pipes if the outage will last. Act in the first hours, before the house cools.

  • Keep doors and windows closed, and gather the household in fewer rooms so you only have to hold heat in a small space.
  • Let faucets on exposed lines drip, so water keeps moving and the pressure has somewhere to go.
  • Wrap exposed pipes with towels, blankets or newspaper as a stopgap until the heat returns. The American Red Cross says even newspaper can give exposed pipes some protection.
  • Use only heaters rated for indoor use, and keep them clear of anything that can burn.
  • If the house will stay below freezing for an extended period, close the main valve and drain the lines, starting with the highest faucet. Check your water heater’s manual before you drain, because some heaters need to be turned off first.

Carbon monoxide safety: Never run a generator or any gasoline-powered engine inside your home, basement or garage. Never use a charcoal grill or portable camping stove inside a home, tent or camper. Never use a gas range or oven to heat your home, and never use an outdoor heater inside your home or an attached garage. The Centers for Disease Control and Prevention (CDC, 2026) also advises a battery-powered or battery backup carbon monoxide detector.

Plug-in devices, including a Bluebot meter and your Wi-Fi router, stop reporting during an outage. A Bluebot meter reconnects and resumes on its own when power returns.

Signs a Pipe Has Frozen and What to Do First

If a faucet gives only a trickle or nothing in freezing weather, assume a pipe is frozen, keep that tap open, and start warming the pipe gently. Working fast matters, because trapped ice can build pressure in the pipe until it splits, and a split can flood a wall or ceiling before you notice.

Warning Signs

If you get little or no water from a tap, suspect a frozen pipe. The American Red Cross says even a trickle is reason enough. Other signs include frost on an exposed pipe, a bulge or crack in the pipe, and odd smells from a drain. In freezing weather, any one of these may mean ice, though a clog can cause some of them too.

First Steps

  1. Keep the faucet open, so water can flow as the ice melts and help melt the rest.
  2. Find the frozen section, usually on an exterior wall or in an unheated space, such as where the water line enters through the foundation.
  3. Warm it with a hair dryer, heating pad or towels soaked in hot water, working from the faucet back toward the blockage. Never use an open flame or a torch, and keep any electrical device away from standing water.
  4. Keep applying gentle heat until full water pressure returns, then check the other faucets, because if one pipe froze, others may have too.
  5. Call a licensed plumber if you cannot find or reach the frozen section, or if water does not return.

If a pipe already burst

  1. Close the main water shut-off valve.
  2. Keep clear of electrical outlets and devices near standing water.
  3. Call a licensed plumber.
  4. Photograph the damage for your insurer.

Speed matters, because water keeps spreading while it runs. For more, see Bluebot’s step-by-step guide on how to stop a water leak fast.

How Bluebot Fits: Catching the Leak a Freeze Leaves Behind

Nothing on this page depends on Bluebot, and a Bluebot meter does not prevent frozen pipes. It watches the water flowing through your main line. It alerts you when water runs that should not, such as the steady flow from a split pipe once it thaws.

A Bluebot smart water meter clamps onto the main water line. You do not need to cut the pipe, shut off your water or hire a plumber to install it. It measures flow and sends real-time alerts through the bluebot Water app. You can hear about a running leak while you are at work, on a trip or asleep.

Bluebot’s short post on how to monitor your water in winter covers the seasonal angle.

What it does not do matters just as much. A Bluebot meter does not prevent freezing and does not close a valve. It reports water flow, not air or pipe temperature, so it is not a freeze alarm. Closing the main valve is still your job, or the job of an automatic shut-off valve.

Pair the meter with a freeze or temperature alarm: the alarm warns you before pipes freeze, and the flow alert covers the burst afterward.

Install note: every Bluebot meter operates at 32°F to 122°F (0°C to 50°C). Mount it on the main line in a heated space, not on an exposed pipe in an unheated crawl space.

The Bottom Line: Prevent What You Can, Catch What You Can’t

Prevent what you can. For frozen pipe prevention, keep the heat on and steady, insulate and seal pipes in unheated spaces, and drain outdoor faucets before the first freeze. Those three steps are the core of the plan to prevent pipes from freezing, and fall is a good time to do each one. Together, they lower the chance that a frozen pipe becomes a burst pipe.

Then take the one readiness step that limits the damage if a pipe splits anyway: find your main water shut-off valve, tag it and make sure it turns.

For the leak a freeze can still leave behind, Bluebot offers whole-home leak alerts that tell you when water runs that should not. A Bluebot meter detects and alerts, so you hear about a running leak fast and can close the valve yourself.

Frozen Pipe Guides: Go Deeper on Each Topic

Each guide below answers one question that this page only summarizes, so pick the one that matches the job in front of you.

  • Freezing points: A full answer to at what temperature do pipes freeze covers indoor, outdoor and in-wall freezing points. It also explains why a pipe in a wall freezes differently from one in a garage.
  • Freeze speed: To learn how long does it take for pipes to freeze, that guide explains how fast pipes freeze once the temperature drops. It also covers what changes the clock.
  • Dripping: Learn when to drip faucets, which ones to open and how much to run them, including hot versus cold sides.
  • Thermostat settings: Find the minimum temp to keep pipes from freezing, at home and away, in the thermostat guide. It gives a clear answer for nights and for trips.
  • Outdoor faucets: Step-by-step help on how to winterize outdoor faucet setups: shutting off, draining and covering hose bibs, for standard and frost-free types.
  • Main shut-off valve: Find your main water shut off valve location and learn how to close it. Then you can act in seconds when a pipe splits and keep the damage small.

Frequently Asked Questions

Will pipes burst if they freeze?

Not always, but they can. A pipe usually splits when an ice blockage traps water between the ice and a closed faucet. Pressure builds until the pipe gives way, often away from the ice itself. A frozen pipe is not safe just because it has not leaked yet, so thaw it carefully and keep the faucet open.

What do you wrap around pipes to keep them from freezing?

Foam pipe sleeves sized to the pipe are the standard pipe insulation. Tape the seams and joints, cover fittings and valves, and use fiberglass wrap in tight spots. For a line you cannot keep warm, thermostatically controlled heat cable listed by a recognized testing lab such as UL can help, installed as the manufacturer directs.

Do you need to drip every faucet to keep pipes from freezing?

No. Choose faucets on exterior walls or fed by exposed pipes, and run a slow drip on both the hot and cold sides. Running water, even a trickle, helps prevent freezing, and an open tap gives pressure behind an ice blockage somewhere to go. If your utility asks customers to limit dripping during a widespread freeze, follow that request.

Should I leave cabinet doors open to prevent frozen pipes?

Yes, during a hard freeze, for cabinets on exterior walls. Open doors let room air reach the pipes behind them, and both the American Red Cross and IBHS (2023) advise it. Move cleaning products and household chemicals out of reach of children and pets first.

How do I keep pipes from freezing in an apartment?

Focus on what you control. Keep the thermostat steady day and night, open cabinet doors on exterior walls, and let a faucet on an exposed line drip during a hard freeze. Ask your building manager where your shut-off valve is, and report a frozen pipe or a leak right away.

How do you keep pipes from freezing in a mobile home?

The same rules apply, with extra attention to any pipe outside the heated space. Insulate exposed pipes with foam sleeves, seal gaps where pipes enter, and keep the heat steady day and night. Heat cable listed by a recognized testing lab such as UL can protect a line you cannot keep warm, installed as the manufacturer directs.

How do I keep pipes from freezing in a crawl space?

Treat a crawl space as an unheated space. Insulate exposed pipes with foam sleeves, tape the seams, and seal air leaks around pipe penetrations and sill plates. IBHS (2023) also advises temporarily covering or closing crawl space vents in winter, so check your local code first.

Should I turn off my water to keep pipes from freezing when I’m away?

It is one of two safe choices. You can keep the heat on, set no lower than 55°F according to the American Red Cross, and have someone check the house. Or you can close the main valve and open faucets, starting on the top floor, to drain the lines. For a long absence, draining removes the water that could freeze.

Can PEX pipes freeze?

Yes. Water inside PEX can still freeze. The Plastics Pipe Institute (2026) says frozen PEX typically expands without cracking or splitting, but installation problems can still make it fail. Insulate PEX in unheated spaces the same way you would any other pipe, and keep the heat steady during a hard freeze.

Does homeowners insurance cover frozen pipes?

Coverage depends on your policy, so read yours or ask your insurer. Some homeowners policies may expect you to take reasonable steps, such as keeping heat on in an unoccupied home, so a written freeze plan helps. If a pipe bursts, close the main valve, call a licensed plumber and photograph the damage for your insurer.

Bluebot Mini Smart Water Meter
Bluebot Mini
Affordable Smart Water Meter
  • Wi-Fi
  • Fits ¾” – 1″ pipes
  • Indoor/Outdoor
Starts at
$25876
+ Includes 1-Year Premium Data
Bluebot Hero - Wi-Fi Smart Water Meter
Bluebot Hero
Flagship Smart Water Meter
  • Wi-Fi
  • Fits ¾” – 2″ pipes
  • Indoor/Outdoor
Starts at
$55834
+ Includes 1-Year Premium Data